 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 4-235-739-11(1) www..com FM Stereo FM-AM Receiver Operating Instructions STR-DE575 STR-K502 2001 Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. CAUTION You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment. Precautions On safety * Should any solid object or liquid fall into the cabinet, unplug the receiver and have it checked by qualified personnel before operating it any further. * To prevent fire, do not cover the ventilation of the receiver with newspapers, table cloths, curtains, etc. And don't place lighted candles on the receiver. * To prevent fire or shock hazards, do not place vases on the receiver. Note to CATV system installer: This reminder is provided to call CATV system installer's attention to Article 82040 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. On power sources * Before operating the receiver, check that the operating voltage is identical with your local power supply. The operating voltage is indicated on the nameplate at the rear of the receiver. * The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. * If you are not going to use the receiver for a long time, be sure to disconnect the receiver from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord. * One blade of the plug is wider than the other for the purpose of safety and will fit into the wall outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer. * AC power cord must be changed only at the qualified service shop. www..com This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Owner's Record The model and serial numbers are located on the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. STR-DE575/K502 Serial No. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. For customers in Canada CAUTION TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. On placement * Place the receiver in a location with adequate ventilation to prevent heat buildup and prolong the life of the receiver. * Do not place the receiver near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. * Do not place anything on top of the cabinet that might block the ventilation holes and cause malfunctions. * Although the receiver heats up during operation, this is not a malfunction. If you continuously use this receiver at a large volume, the cabinet temperature of the top, side and bottom rises accordingly. To avoid burning yourself, do not touch the cabinet. For customers in the United States and Canada ENERGY STAR(R) is a U.S. registered mark. As an ENERGY STAR(R) partner, Sony Corporation has determined that this product meets the ENERGY STAR(R) guidelines for energy efficiency. Don't throw a battery, dispose it as the injurious wastes. On operation Before connecting other components, be sure to turn off and unplug the receiver. On cleaning Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. If you have any question or problem concerning your receiver, please consult your nearest Sony dealer. 2 About This Manual The instructions in this manual are for the STR-DE575 and STR-K502. Check your model number by looking at the lower right corner of the front panel or lower right corner of the remote. In this manual, the STR-DE575 and the remote commander RM-U305 are used for illustration purposes unless stated otherwise. Any difference in operation is clearly indicated in the text, for example, "STR-DE575 only". About area codes The area code of the player you purchased is shown on the lower portion of the rear panel (see the illustration below). www..com TABLE OF CONTENTS Hooking Up the Components 4 Unpacking 4 Antenna Hookups 5 Audio Component Hookups 6 Video Component Hookups 7 Digital Component Hookups 8 MULTI CH IN Hookups 9 Other Hookups 10 Hooking Up and Setting Up the Speaker System 11 Speaker System Hookup 12 Performing Initial Setup Operations Multi Channel Surround Setup 15 Before You Use Your Receiver 19 14 ERS CENTER IMPEDANCE USE 8 - 16 FRONT R L R L 4-XXX-XXX-XX AA Area code Any differences in operation, according to the area code, are clearly indicate in the text, for example, "Models of area code AA only". Location of Parts and Basic Operations 21 Front Panel Parts Descriptions 21 Conventions * The instructions in this manual describe the controls on the receiver. You can also use the controls on the supplied remote if they have the same or similar names as those on the receiver. * The following icon is used in this manual: z Indicates hints and tips for making the task easier. This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System. Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic" and the double-D symbol a are trademarks of Dolby Laboratories. Confidential unpublished Works. (c) 1992-1997 Dolby Laboratories. All rights reserved. **Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942, 5,956,674, 5,974,380, 5,978,762 and other world-wide patents issued and pending. "DTS" and "DTS Digital Surround" are registered trademarks of Digital Theater Systems, Inc. Copyright 1996, 2000 Digital Theater Systems, Inc. All Rights Reserved. Enjoying Surround Sound 25 Selecting a Sound Field 26 Understanding the Multi-Channel Surround Displays 30 Customizing Sound Fields 32 Receiving Broadcasts 36 Direct Tuning 38 Automatic Tuning 38 Preset Tuning 39 * Other Operations 40 Naming Preset Stations and Program Sources 41 Recording 41 Using the Sleep Timer 42 Adjustment Using the SET UP Button 43 Additional Information 44 Troubleshooting 44 Specifications 46 Glossary 48 Settings Using SURR, LEVEL, EQ, and SET UP buttons 49 Remote Button Description 50 Index 53 3 Hooking Up the Components This chapter describes how to connect various audio and video components to the receiver. Be sure to read the sections for the components you have www..com you actually connect them to before the receiver. Unpacking Check that you received the following items with the receiver: * FM wire antenna (1) * AM loop antenna (1) * R6 (size-AA) batteries (2) * Remote commander RM-U305 (remote) (1) Inserting batteries into the remote Insert R6 (size-AA) batteries with the + and - properly oriented in the battery compartment. When using the remote, point it at the remote sensor g on the receiver. ] } ] } z When to replace batteries Under normal conditions, the batteries should last for about 6 months. When the remote no longer operates the receiver, replace all batteries with new ones. Notes * Do not leave the remote in an extremely hot or humid place. * Do not use a new battery with an old one. * Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction. * If you don't use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. Before you get started * Turn off the power to all components before making any connections. * Do not connect the AC power cords until all of the connections are completed. * Be sure to make connections firmly to avoid hum and noise. * When connecting an audio/video cord, be sure to match the color-coded pins to the appropriate jacks on the components: yellow (video) to yellow; white (left, audio) to white; and red (right, audio) to red. 4 Antenna Hookups AM loop antenna (supplied) FM wire antenna (supplied) Hooking Up the Components DIGITAL OPTICAL DVD/LD IN ANTENNA TV/SAT IN AM MONITOR www..com VIDEO IN VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT DVD/LD IN COAXIAL FM 75 COAXIAL SPEAKERS SURROUND R L CENTER IMPEDANCE USE 8 - 16 FRONT R L S VIDEO IN S VIDEO OUT L L CENTER L L L AUDIO OUT R R FRONT SURROUND SUB WOOFER IN R IN OUT R IN AUDIO IN R AUDIO IN R AUDIO OUT AUDIO IN L R L MULTI CH IN AUX CD MD/TAPE TV/SAT DVD/LD VIDEO SUB WOOFER Terminals for connecting the antennas Connect the AM loop antenna FM wire antenna z If you have poor FM reception Use a 75-ohm coaxial cable (not supplied) to connect the receiver to an outdoor FM antenna as shown below. Outdoor FM antenna Receiver ANTENNA To the AM terminals FM 75 COAXIAL terminal Notes on antenna hookups * To prevent noise pickup, keep the AM loop antenna away from the receiver and other components. * Be sure to fully extend the FM wire antenna. * After connecting the FM wire antenna, keep it as horizontal as possible. AM FM 75 COAXIAL Ground wire (not supplied) To ground Important If you connect the receiver to an outdoor antenna, ground it against lightning. To prevent a gas explosion, do not connect the ground wire to a gas pipe. 5 Audio Component Hookups Required cords Hooking Up the Components Audio cords (not supplied) MD/TAPE deck INPUT OUTPUT LINE LINE L When connecting a cord, be sure to match the color-coded pins to the appropriate jacks on the components. White (L) White (L) Red (R) R Red (R) IN OUT c DIGITAL OPTICAL DVD/LD IN c www..com ANTENNA TV/SAT IN AM MONITOR VIDEO IN VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT DVD/LD IN COAXIAL FM 75 COAXIAL SPEAKERS SURROUND R L CENTER IMPEDANCE USE 8 - 16 FRONT R L S VIDEO IN S VIDEO OUT L L CENTER L L L AUDIO OUT R R FRONT SURROUND SUB WOOFER IN R IN OUT R IN AUDIO IN R AUDIO IN R AUDIO OUT AUDIO IN L R L MULTI CH IN AUX CD MD/TAPE TV/SAT DVD/LD VIDEO SUB WOOFER OUTPUT LINE L R CD player Jacks for connecting audio components Connect a CD player MD deck or Tape deck To the CD jacks MD/TAPE jacks 6 Video Component Hookups Required cords Hooking Up the Components Audio/video cords (not supplied) When connecting a cord, be sure to match the color-coded pins to the appropriate jacks on the components. Yellow (video) TV or satellite tuner OUTPUT AUDIO OUT R L VIDEO OUT Yellow (video) White (L/audio) Red (R/audio) DVD or LD player * S-VIDEO OUTPUT AUDIO OUT R L VIDEO OUT OUT TV monitor * S-VIDEO INPUT VIDEO IN IN White (L/audio) Red (R/audio) Video cord for connecting a TV monitor (not supplied) www..com Yellow Yellow DIGITAL OPTICAL DVD/LD IN ANTENNA TV/SAT IN AM MONITOR VIDEO IN VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT DVD/LD IN COAXIAL FM 75 COAXIAL SPEAKERS SURROUND R L CENTER IMPEDANCE USE 8 - 16 FRONT R L S VIDEO IN S VIDEO OUT L L CENTER L L L AUDIO OUT R R FRONT SURROUND SUB WOOFER IN R IN OUT R IN AUDIO IN R AUDIO IN R AUDIO OUT AUDIO IN L R L MULTI CH IN AUX CD MD/TAPE TV/SAT DVD/LD VIDEO SUB WOOFER c IN INPUT OUTPUT VIDEO IN VIDEO OUT c OUT AUDIO IN AUDIO OUT L R VCR * STR-DE575 only. Jacks for connecting video components Connect a TV or satellite tuner VCR DVD or LD player TV monitor Note on video component hookups You can connect your TV's audio output jacks to the TV/ SAT AUDIO IN jacks on the receiver and apply sound effects to the audio from the TV. In this case, do not connect the TV's video output jack to the TV/SAT VIDEO IN jack on the receiver. If you are connecting a separate TV tuner (or satellite tuner), connect both the audio and video output jacks to the receiver as shown above. To the TV/SAT jacks VIDEO jacks DVD/LD jacks MONITOR VIDEO OUT jack z When using the S-video jacks instead of the video jacks Your monitor must also be connected via an S-video jack. S-video signals are on a separate bus from the video signals and will not be output through the video jacks. (STR-DE575 only) 7 Digital Component Hookups Connect the digital output jacks of your DVD player and satellite tuner (etc.) to the receiver's digital input jacks to bring the multi channel surround sound of a movie theater into your home. To enjoy full effect of multi channel surround sound, five speakers (two front speakers, two surround speakers, and a center speaker) and a sub woofer are required. You can also connect an LD player with an RF OUT jack via an RF demodulator, such as the Sony MOD-RF1 (not supplied). Required cords Optical digital cords (not supplied) Black Black www..com Hooking Up the Components Coaxial digital cord (not supplied) Yellow Yellow Audio/video cords (not supplied) When connecting a cord, be sure to match the color-coded pins to the appropriate jacks on the components. Yellow (video) White (L/audio) Red (R/audio) Yellow (video) White (L/audio) Red (R/audio) DVD or LD player (etc.)* OUTPUT VIDEO OUT TV or Satellite tuner OUTPUT VIDEO OUT AUDIO OUT AUDIO OUT L Note The optical and coaxial digital input jacks on the receiver are compatible with sampling frequencies of 32 kHz, 44.1 kHz, and 48kHz. OUTPUT DIGITAL OPTICAL OUTPUT DIGITAL COAXIAL OUTPUT DIGITAL OPTICAL R DIGITAL OPTICAL DVD/LD IN ANTENNA TV/SAT IN AM MONITOR VIDEO IN VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT DVD/LD IN COAXIAL FM 75 COAXIAL SPEAKERS SURROUND R L CENTER IMPEDANCE USE 8 - 16 FRONT R L S VIDEO IN S VIDEO OUT L L CENTER L L L AUDIO OUT R R FRONT SURROUND SUB WOOFER IN R IN OUT R IN AUDIO IN R AUDIO IN R AUDIO OUT AUDIO IN L R L MULTI CH IN AUX CD MD/TAPE TV/SAT DVD/LD VIDEO SUB WOOFER * When making digital audio connections to a DVD player, connect to either the coaxial OR optical digital jacks, and not both. It is recommended to make digital audio connections to the coaxial jack. Example of LD player connected via an RF demodulator Please note that you cannot connect an LD player's DOLBY DIGITAL RF OUT jack directly to the receiver's digital input jacks. You must first convert the RF signal to either an optical or coaxial digital signal. Connect the LD player to the RF demodulator, then connect the RF demodulator's optical or coaxial digital output to the receiver's OPTICAL or COAXIAL DVD/LD IN jack. Refer to the instruction manual supplied with your RF Demodulator for details on DOLBY DIGITAL RF hookups. VIDEO OUT LD player DOLBY DIGITAL RF OUT RF demodulator DVD/LD VIDEO IN MULTI CHANNEL DECODING VIDEO DVD/LD TV/SAT DIGITAL DIGITAL DVD/LD IN DVD/LD IN (COAXIAL) (COAXIAL) (OPTICAL) or (OPTICAL) ?/1 MD/TAPE INPUT MODE MASTER VOLUME CD TUNER AUX + SPEAKERS DISPLAY PRESET TUNING EQ LEVEL SURR SET UP NAME A CINEMA STUDIO EX B SOUND FIELD A.F.D. ENTER MODE 2CH C MULTI CH IN MUTING EQUALIZER - DIMMER - + - TUNING + MEMORY PHONES SHIFT FM MODE FM AM Note When making connections as shown above, be sure to set INPUT MODE (8 on page 23) manually. The receiver may not operate correctly if INPUT MODE is set to "AUTO." 8 MULTI CH IN Hookups Although this receiver incorporates a multi channel decoder, it is also equipped with MULTI CH IN jacks. These connections allow you to enjoy multichannel software encoded in formats other than Dolby Digital and DTS. If your DVD player is equipped with MULTI CH OUTPUT jacks, you can connect them directly to the receiver to enjoy the sound of the DVD player's multi channel decoder. Alternatively, the MULTI CH IN jacks can be used to connect an external multi channel decoder. To fully enjoy multi channel surround sound, you will need five speakers (two front speakers, two surround speakers, and a center speaker) and a sub woofer. Refer to www..com the instruction manual supplied with your DVD player, multi channel decoder, etc., for details on the multi channel input hookups. Required cords Hooking Up the Components Audio cords (not supplied) Two for the MULTI CH IN FRONT and SURROUND jacks White (L) Red (R) White (L) Red (R) Monaural audio cords (not supplied) Two for the MULTI CH IN CENTER and SUB WOOFER jacks Black Black Video cord (not supplied) One for the DVD/LD VIDEO IN jacks (etc.) Yellow Yellow DVD player, Multichannel decoder, etc. MULTI CH OUTPUT SURROUND Note When using the connections described below, adjust the level of your surround speakers and sub woofer from the DVD player or multichannel decoder. FRONT CENTER SUB WOOFER DIGITAL OPTICAL DVD/LD IN ANTENNA TV/SAT IN AM MONITOR VIDEO IN VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT DVD/LD IN COAXIAL FM 75 COAXIAL SPEAKERS SURROUND R L CENTER IMPEDANCE USE 8 - 16 FRONT R L S VIDEO IN S VIDEO OUT L L CENTER L L L AUDIO OUT R R FRONT SURROUND SUB WOOFER IN R IN OUT R IN AUDIO IN R AUDIO IN R AUDIO OUT AUDIO IN L R L MULTI CH IN AUX CD MD/TAPE TV/SAT DVD/LD VIDEO SUB WOOFER Example of a DVD player hookup using the MULTI CH IN jacks Front Speaker (L) Front Speaker (R) VIDEO OUT MULTI CH IN ?/1 MD/TAPE INPUT MODE MASTER VOLUME DVD/LD IN VIDEO etc. MULTI CHANNEL DECODING VIDEO DVD/LD TV/SAT CD TUNER AUX SPEAKERS FRONT + Surround Speaker (L) Surround Speaker (R) DVD player SPEAKERS DISPLAY PRESET TUNING EQ LEVEL SURR SET UP NAME A CINEMA STUDIO EX B SOUND FIELD A.F.D. ENTER MODE 2CH C MULTI CH IN MUTING EQUALIZER - SPEAKERS SURROUND/CENTER SUB WOOFER DIMMER - + - TUNING + Center Speaker Active Woofer MEMORY PHONES SHIFT FM MODE FM AM Note See page 12 for details on speaker system hookup. 9 Other Hookups Required cords Hooking Up the Components Audio cords (not supplied) When connecting a cord, be sure to match the color-coded pins to the appropriate jacks on the components. White (L) Red (R) White (L) Red (R) AC power cord www..com OPTICAL DVD/LD IN TV/SAT IN DIGITAL ANTENNA AM MONITOR VIDEO IN VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT DVD/LD IN COAXIAL FM 75 COAXIAL SPEAKERS SURROUND R L CENTER IMPEDANCE USE 8 - 16 FRONT R L S VIDEO IN S VIDEO OUT L L CENTER L L L AUDIO OUT R R FRONT SURROUND SUB WOOFER IN R IN OUT R IN AUDIO IN R AUDIO IN R AUDIO OUT AUDIO IN L R L MULTI CH IN AUX CD MD/TAPE TV/SAT DVD/LD VIDEO SUB WOOFER OUTPUT LINE To a wall outlet CD player, tape deck, MD deck, etc. AUX AUDIO IN hookup * If you have an individual audio component (except PHONO) Use the audio cords to connect the LINE OUT jacks on the CD player, tape deck, or MD deck to the AUX AUDIO IN jack on the receiver so that you can listen to stereo sources in surround sound. Connecting the AC power cord Before connecting the AC power cord of this receiver to a wall outlet: * Connect the speaker system to the receiver (see page 12). Connect the AC power cord(s) of your audio/video components to a wall outlet. Note If the AC power cord is disconnected for about one week, the receiver's entire memory will be cleared and the demonstration will start. 10 Hooking Up and Setting Up the Speaker System This chapter describes how to hook up your speaker system to the www..com receiver, how to position each speaker, and how to set up your speakers to enjoy multi channel surround sound. SET UP Jog dial MULTI CHANNEL DECODING VIDEO DVD/LD TV/SAT ?/1 MD/TAPE INPUT MODE MASTER VOLUME CD TUNER AUX + SPEAKERS DISPLAY PRESET TUNING EQ LEVEL SURR SET UP NAME A CINEMA STUDIO EX B SOUND FIELD A.F.D. ENTER MODE 2CH C MULTI CH IN MUTING EQUALIZER - DIMMER - + - TUNING + MEMORY PHONES SHIFT FM MODE FM AM Hooking Up and Setting Up the Speaker System Cursor buttons Brief descriptions of buttons and control used to set up the speaker system SET UP button: Press to enter the setup mode when specifying speaker types and distances. Cursor buttons ( / ): Use to select parameters after pressing the SET UP button. Jog dial: Use to adjust the setting of each parameter. 11 Speaker System Hookup Required cords Speaker cords (not supplied) One for each front, surround, and center speaker (+) (-) (+) (-) Front speaker (R) Front speaker (L) www..com DIGITAL OPTICAL DVD/LD IN Hooking Up and Setting Up the Speaker System Monaural audio cord (not supplied) One for an active woofer Black Black } ] } ] ANTENNA TV/SAT IN AM MONITOR VIDEO IN VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT DVD/LD IN COAXIAL FM 75 COAXIAL SPEAKERS SURROUND R L CENTER IMPEDANCE USE 8 - 16 FRONT R L S VIDEO IN S VIDEO OUT L L CENTER L L L AUDIO OUT R R FRONT SURROUND SUB WOOFER IN R IN OUT R IN AUDIO IN R AUDIO IN R AUDIO OUT AUDIO IN L R L MULTI CH IN AUX CD MD/TAPE TV/SAT DVD/LD VIDEO SUB WOOFER INPUT AUDIO IN } ] } ] } ] Active sub woofer Surround speaker (R) Surround speaker (L) Center speaker Terminals for connecting the speakers Connect the Front speakers (8 ohm) Surround speakers (8 ohm) Center speaker (8 ohm) Active sub woofer Notes on speaker system hookup * Twist the stripped ends of the speaker cords about 2/3 inch (10 mm). Be sure to match the speaker cord to the appropriate terminal on the components: + to + and - to -. If the cords are reversed, the sound will be distorted and will lack bass. * If you use speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on the speakers. To the SPEAKERS FRONT terminals SPEAKERS SURROUND terminals SPEAKERS CENTER terminals SUB WOOFER AUDIO OUT jack 12 To avoid short-circuiting the speakers Short-circuiting of the speakers may damage the receiver. To prevent this, make sure to take the following precautions when connecting the speakers. Make sure the stripped ends of each speaker cord does not touch another speaker terminal or the stripped end of another speaker cord. Examples of poor conditions of the speaker cord www..com Hooking Up and Setting Up the Speaker System Stripped speaker cord is touching another speaker terminal. Stripped cords are touching each other due to excessive removal of insulation. After connecting all the components, speakers, and AC power cord, output a test tone to check that all the speakers are connected correctly. For details on outputting a test tone, see page 18. If no sound is heard from a speaker while outputting a test tone or a test tone is output from a speaker other than the one whose name is currently displayed on the receiver, the speaker may be short-circuited. If this happens, check the speaker connection again. To avoid damaging your speakers Make sure that you turn down the volume before you turn off the receiver. When you turn on the receiver, the volume remains at the level you turn off the receiver. 13 Performing Initial Setup Operations Once you have hooked up the speakers and turned on the power, clear the receiver's memory. Then specify the speaker parameters (size, position, etc.) and perform any other initial setup operations necessary for your system. Performing initial setup operations Before you use your receiver for the first time, use the SET UP button to adjust settings to correspond to your system. You can set the following items. For details on how to adjust each setting, see the page in parentheses. * Speaker size and placement (page 15). * Speaker distance (page 17). * Select the MULTI CH IN video signal (page 43). * Whether the display turns off or not when you press DIMMER (page 43). Demonstration Mode Clearing the receiver's memory Before you use your receiver for the first time or when you want to clear the receiver's memory, do the following. This procedure is not necessary if the demonstration activates when you turn the power on. 1/u www..com Hooking Up and Setting Up the Speaker System MULTI CHANNEL DECODING VIDEO DVD/LD TV/SAT ?/1 MD/TAPE INPUT MODE MASTER VOLUME CD TUNER AUX + SPEAKERS DISPLAY PRESET TUNING EQ LEVEL SURR SET UP NAME A CINEMA STUDIO EX B SOUND FIELD A.F.D. ENTER MODE 2CH C MULTI CH IN MUTING EQUALIZER - DIMMER - + - TUNING + MEMORY PHONES SHIFT FM MODE FM AM The demonstration will activate the first time you turn on the power. When the demonstration starts, the following message appears in the display: "NOW DEMONSTRATION MODE IF YOU FINISH DEMONSTRATION PLEASE PRESS POWER KEY WHILE THIS MESSAGE APPEARS IN THE DISPLAY THANK YOU" To cancel the demonstration 1 2 Turn off the receiver. Hold down ?/1 for four seconds. The currently selected function, then the demonstration message appears in the display and the items including the following are reset or cleared: * All preset stations are reset or cleared. * All sound field parameters are reset to their factory settings. * All index names (of preset stations and program sources) are cleared. * All adjustments made with the SET UP button are reset to their factory settings. * The sound field memorized for each program source and preset stations are cleared. Press ?/1 to turn the receiver off while the above message is being displayed. The next time you turn the receiver on, the demonstration will not appear. To view the demonstration Hold down SET UP and press ?/1 to turn on the power. Notes * Running the demonstration will clear the receiver's memory. For details on what will be cleared, see "Clearing the receiver's memory" on this page. * There will be no sound when the demonstration mode is activated. * You cannot cancel demonstration if you did not press ?/1 while the above message is being displayed. To cancel demonstration after the above message appears, press ?/1 twice to activate the demonstration again. Then, press ?/1 while the above message is being displayed. 14 Multi Channel Surround Setup For the best possible surround sound all speakers should be the same distance from the listening position (A). (However, this unit lets you to place the center speaker up to 5 feet (1.5 meters) closer (B) and the surround speakers up to 15 feet (4.5 meters) closer (C) to the listening position. The front speakers can be placed from 3 to 40 feet (1.0 to 12.0 meters) from the listening position (A).) You can place the surround speakers either behind you or to the side, depending on the shape of your room (etc.). When placing surround speakers to your side www..com B A 45 A Specifying the speaker parameters 1 2 3 4 5 Press ?/1 to turn on the receiver. Press SET UP. Hooking Up and Setting Up the Speaker System Press the cursor buttons ( or parameter you want to adjust. ) to select the Turn the jog dial to select the setting you want. The setting is stored automatically. Repeat steps 3 and 4 until you have set all of the parameters that follow. z Normal speaker and Micro Satellite speaker Choose NORM. SP. if you're using normal speakers and MICRO SP. if you're using Micro Satellite speakers. If you choose NORM. SP., you can adjust the speaker size and the sub woofer selection as mentioned below. However, if you choose MICRO SP., the speaker size and the sub woofer selection has been configurated as follows: C 90 C Speakers Front 20 Settings SMALL SMALL SMALL YES Center Surround When placing the surround speakers behind you Woofer B A 45 A You cannot change the configuration if you choose MICRO SP. For STR-K502, the speaker size and sub woofer selection has been preset to MICRO SP. according to the supplied speaker system. If you change the speaker system, choose NORM. SP. to adjust the speaker size and sub woofer selection. C 90 C The setting for Micro Satellite speaker (MICRO SP.) has been programmed to optimize the sound balance. If you use Sony's Micro Satellite speakers, select MICRO SP. When you use Micro Satellite speaker and the speaker size is set to LARGE, you may not obtain the correct soundstage. The speaker may also be damaged at high volume position. For STR-DE575, the speaker size and sub woofer selection has been preset to NORM. SP. The following speaker size setup is applicable for NORM. SP. 20 Note Do not place the center speaker farther away from the listening position than the front speakers. 15 Multi Channel Surround Setup R) x Front speaker size ( L Initial setting : LARGE * If you connect large speakers that will effectively reproduce bass frequencies, select "LARGE". Normally, select "LARGE". * If the sound is distorted, or you feel a lack of surround effects when using multi channel surround sound, select "SMALL" to activate the bass redirection circuitry and output the front channel bass frequencies from the sub woofer. * When the front speaker is set to "SMALL", the center and surround speakers are also automatically set to "SMALL" (unless previously set to "NO"). z About speaker sizes (LARGE and SMALL) Internally, the LARGE and SMALL settings for each speaker determine whether or not the internal sound processor will cut the bass signal from that channel. When the bass is cut from a channel the bass redirection circuitry sends the corresponding bass frequencies to the sub woofer or other "LARGE" speaker. However, since bass sounds have a certain amount of directionality it best not to cut them, if possible. Therefore, even when using small speakers, you can set them to "LARGE" if you want to output the bass frequencies from that speaker. On the other hand, if you are using a large speaker, but prefer not to have bass frequencies output from that speaker, set it to "SMALL". If the overall sound level is lower than you prefer, set all speakers to "LARGE". If there is not enough bass, you can use the equalizer to boost the bass levels. To adjust the equalizer see page 34. www..com p Center speaker size ( Hooking Up and Setting Up the Speaker System C) Initial setting : LARGE * If you connect a large speaker that will effectively reproduce bass frequencies, select "LARGE". Normally, select "LARGE". However, if the front speakers are set to "SMALL", you cannot set the center speaker to "LARGE". * If the sound is distorted, or you feel a lack of surround effects when using multi channel surround sound, select "SMALL" to activate the bass redirection circuitry and output the center channel bass frequencies from the front speakers (if set to "LARGE") or sub woofer. *1 * If you do not connect the center speaker, select "NO". The sound of the center channel will be output from the front speakers.*2 x Surround speaker position ( SL SR )* p Surround speaker size ( SL SR ) Initial setting : LARGE * If you connect large speakers that will effectively reproduce bass frequencies, select "LARGE". Normally, select "LARGE". However, if the front speakers are set to "SMALL", you cannot set the surround speakers to "LARGE". * If the sound is distorted, or you feel a lack of surround effects when using multi channel surround sound, select "SMALL" to activate the bass redirection circuitry and output the surround channel bass frequencies from the sub woofer or other "LARGE" speakers. * If you do not connect surround speakers, select "NO".*3 Initial setting : PL. BEHD. This parameter lets you specify the location of your surround speakers for proper implementation of the Digital Cinema Sound surround modes in the "VIRTUAL" sound fields. Refer to the illustration below. * Select "PL. SIDE" if the location of your surround speakers corresponds to section A. * Select "PL. MID" if the location of your surround speakers corresponds to section B. * Select "PL. BEHD." if the location of your surround speakers corresponds to section C. This setting only effects the surround modes in the "VIRTUAL" sound fields. 90 A 60 B C 20 30 C B A z *1~*3 correspond to the following Dolby Pro Logic modes *1 NORMAL *2 PHANTOM *3 3 STEREO * These parameters are not available when "Surround speaker size" is set to "NO". 16 x Surround speaker height ( SL SR )* www..com Initial setting : HGT. LOW This parameter lets you specify the height of your surround speakers for proper implementation of the Digital Cinema Sound surround modes in the "VIRTUAL" sound fields. Refer to the illustration below. * Select "HGT. LOW" if the location of your surround speakers corresponds to section A. * Select "HGT. HIGH" if the location of your surround speakers corresponds to section B. This setting only affects the surround modes in the "VIRTUAL" sound fields. x Sub woofer selection Initial setting : S.W. YES * If you connect a sub woofer, select "S.W. YES". * If you do not connect a sub woofer, select "S.W. NO". This activates the bass redirection circuitry and outputs the LFE signals from other speakers. * In order to take full advantage of the Dolby Digital bass redirection circuitry, we recommend setting the sub woofer's cut off frequency as high as possible. R) x Front speaker distance ( L Initial setting : DIST. 5.0 m (5.0 meter) 16 feet Set the distance from your listening position to the front (left or right) speaker (A on page 15). * Front speaker distance can be set in 1 foot (0.1 meter) steps from 3 to 40 feet (1.0 to 12.0 meters). * If both speakers are not placed an equal distance from your listening position, set the distance to the closest speaker. Hooking Up and Setting Up the Speaker System B B A 60 30 A * These parameters are not available when "Surround speaker size" is set to "NO". z About the surround speaker position (PL. SIDE, PL. MID and PL. BEHD.) This setting is designed specifically for implementation of the Digital Cinema Sound modes in the "VIRTUAL" sound fields. With the Digital Cinema Sound modes, speaker position is not as critical as other modes. All of the modes in the "VIRTUAL" sound fields were designed under the premise that the surround speaker would be located behind the listening position, but presentation remains fairly consistent even with the surround speakers positioned at a rather wide angle. However, if the speakers are pointing toward the listener from the immediate left and right of the listening position, the "VIRTUAL" sound fields will not be effective unless the surround speaker position parameter is set to "PL. SIDE". Nevertheless, each listening environment has many variables, such as wall reflections, and you may obtain better results using "PL. BEHD" or "PL. MID" if your speakers are located high above the listening position, even if they are to the immediate left and right. Therefore, although it may result in a setting contrary to the "Surround speaker position" explanation, we recommend that you play back multi channel surround encoded software and listen to the effect each setting has on your listening environment. Choose the setting that provides a good sense of spaciousness and that best succeeds in forming a cohesive space between the surround sound from the surround speakers and the sound from the front speakers. If you are not sure which sounds best, select "PL. BEHD." and then use the speaker distance parameter and speaker level adjustments to obtain proper balance. x Center speaker distance ( C ) Initial setting : DIST. 5.0 m (5.0 meter) 16 feet Set the distance from your listening position to the center speaker. * Center speaker distance can be set in 1 foot (0.1 meter) steps from a distance equal to the front speaker distance (A on page 15) to a distance 5 feet (1.5 meters) closer to your listening position (B on page 15). * Do not place the center speaker farther away from your listening position than the front speakers. x Surround speaker distance ( SL SR ) Initial setting : DIST. 3.5 m (3.5 meter) 11 feet Set the distance from your listening position to the surround (left or right) speaker. * Surround speaker distance can be set in 1 foot (0.1 meter) steps from a distance equal to the front speaker distance (A on page 15) to a distance 15 feet (4.5 meters) closer to your listening position (C on page 15). * Do not place the surround speakers farther away from your listening position than the front speakers. * If both speakers are not placed an equal distance from your listening position, set the distance to the closest speaker. 17 Multi Channel Surround Setup z About speaker distances This receiver allows you to input the speaker position in terms of distance. However, it is not possible to set the center speaker farther away than the front speakers. Also, the center speaker can not be set more that 5 feet (1.5 meters) closer than the front speakers. Likewise, the surround speakers cannot be set farther away from the listening position than the front speakers. And they can be no more than 15 feet (4.5 meters) closer. This is because incorrect speaker placement is not conducive to enjoy the surround sound. Please note that, setting the speaker distance closer than the actual location of the speakers will cause a delay in the output of the sound www..com from that speaker. In other words, the speaker will sound like it is farther away. For example, setting the center speaker distance 3~6 feet (1~2 m) closer than the actual speaker position will create a fairly realistic sensation of being "inside" the screen. If you cannot obtain a satisfactory surround effect because the surround speakers are too close, setting the surround speaker distance closer (shorter) than the actual distance will create a larger soundstage. (1 foot corresponds to a 1 ms difference.) Adjusting these parameters while listening to the sound often results in much better surround sound. Give it a try! Adjusting the speaker volume Use the remote while seated in your listening position to adjust the volume of each speaker. Note This receiver incorporates a new test tone with a frequency centered at 800 Hz for easier speaker volume adjustment. Hooking Up and Setting Up the Speaker System 1 2 Press ?/1 to turn on the receiver. Press TEST TONE on the supplied remote. You will hear the test tone from each speaker in sequence. Adjust the volume level so that the volume of the test tone from each speaker sounds the same when you are in your main listening position. * To adjust the balance of the front right and front left speakers, use the front balance parameter in the LEVEL menu (see page 33). * To adjust the balance of the surround right and surround left speakers, use the surround balance parameter in the LEVEL menu (see page 33). * To adjust the volume level of the center speaker, press MENU to select the center parameter. Use +/- on the remote to adjust the level. * To adjust the volume level of the surround speaker, press MENU to select the surround parameter. Use +/- on the remote to adjust the level. Press TEST TONE on the remote again to turn off the test tone. 3 4 Note The test tone cannot be output when the receiver is set to MULTI CH IN. z You can adjust the volume level of all speakers at the same time Rotate MASTER VOLUME on the receiver or press MASTER VOL +/- on the remote. 18 Before You Use Your Receiver Notes * The front balance, surround balance, center level, and surround level are shown in the display during adjustment. * Although these adjustments can also be made via the front panel using the LEVEL menu (when the test tone is output, the receiver switches to the LEVEL menu automatically), we recommend you follow the procedure previously described in this section and adjust the speaker levels from your listening position using the remote control. Checking the connections After connecting all of your components to the receiver, do the following to verify that the connections were made correctly. 1/u Function buttons Hooking Up and Setting Up the Speaker System MULTI CHANNEL DECODING VIDEO DVD/LD TV/SAT ?/1 MD/TAPE CD TUNER AUX z When setting the volume levels for each speaker Let's assume that you have matched the sound levels of all the speakers using the test tone. Although this lays the foundation for high quality surround sound, it may be necessary to make www..com further adjustments while listening to playback of actual software. This is because most software contains center and surround channels recorded at slightly lower levels than the two front channels. When you actually play back software recorded in multi channel surround, you will notice that increasing the center and surround speaker levels produces a better blend between the front and center speakers and greater cohesion between the front and surround speakers. Increasing the level of the center speaker about 1 dB, and the surround speakers about 1~2 dB is likely to produce better results. In other words, in order to create a more cohesive soundstage with balanced dialog, we recommend that you make some adjustments while playing your software. Changes of only 1 dB can make a huge difference in the character of the soundstage. SPEAKERS DISPLAY PRESET TUNING EQ LEVEL SURR SET UP NAME A CINEMA STUDIO EX B SOUND FIELD A.F.D. ENTER MODE 2CH C DIMMER - + - TUNING + MEMORY PHONES SHIFT FM MODE FM AM INPUT MODE MASTER VOLUME + EQUALIZER - MULTI CH IN MUTING MASTER VOLUME 1 2 Press ?/1 to turn on the receiver. Press a function button to select a component (program source) that you connected (e.g., CD player or tape deck). Turn on the component and start playing it. Rotate MASTER VOLUME to turn up the volume. 3 4 If you do not obtain normal sound output after performing this procedure, look for the reason in the following checklist and take the appropriate measures to correct the problem. There is no sound no matter which component is selected. , Check that both the receiver and all components are turned on. , Check that the volume level on the display is not set to VOL MIN by turning the MASTER VOLUME. , Check that the SPEAKERS button is not set to OFF. , Check that all speaker cords are connected correctly. , Press MUTING if MUTING appears on the display. , Check that the headphones are not connected to the PHONES jack. No sound will come from the speakers if the headphones are connected. , Check that the receiver is not in "Demonstration Mode" (see page 14). 19 Before You Use Your Receiver There's no sound from a specific component. , Check that the component is connected correctly to the audio input jacks for that component. , Check that the cord(s) used for the connection is (are) fully inserted into the jacks on both the receiver and the component. No sound is heard from one of the front speakers. , Connect a pair of headphones to the PHONES jack to verify that sound is output from the headphones (see "qf SPEAKERS button" and "PHONES jack" www..comon page 23). If only one channel is output from the headphones, the component may not be connected to the receiver correctly. Check that all the cords are fully inserted into the jacks on both the receiver and the component. If both channels are output from the headphones, the front speaker may not be connected to the receiver correctly. Check the connection of the front speaker which is not outputting any sound. If you encounter a problem that is not included above, see "Troubleshooting" on page 44. Hooking Up and Setting Up the Speaker System 20 Location of Parts and Basic Operations This chapter provides information about the locations and functions of the buttons and controls on the front panel. It also explains basic www..com operations. Front Panel Parts Descriptions Location of Parts and Basic Amplifier Operations 1 ?/1 switch Press to turn the receiver on and off. 2 DISPLAY button Press repeatedly to change the information on the display window as follows: v Index name of the component or the preset station* v FUNCTION button indication or frequency** v Sound field applied to the program source * Index name appears only when you have assigned one to the component or preset station (see page 41). Index name does not appear when only blank spaces have been entered, or it is the same as the function button. ** Frequency appears only when the tuner is selected. 3 DIMMER button Press repeatedly to adjust the brightness of the display. When you want to turn off the display, set in the "DIM.RANGE" parameter in the SET UP menu (page 43). 21 Front Panel Parts Description 1 23 4 5 6 7 8 9 MULTI CHANNEL DECODING VIDEO DVD/LD TV/SAT ?/1 MD/TAPE INPUT MODE MASTER VOLUME CD TUNER AUX + SPEAKERS DISPLAY PRESET TUNING EQ LEVEL SURR SET UP NAME A CINEMA STUDIO EX B SOUND FIELD A.F.D. ENTER MODE 2CH C MULTI CH IN MUTING EQUALIZER - DIMMER - + - TUNING + www..com PHONES Location of Parts and Basic Amplifier Operations MEMORY SHIFT FM MODE FM AM qf 4 The following buttons operate the built-in tuner. For details, see "Receiving Broadcasts" starting from page 36. PRESET TUNING +/- buttons Scan all preset stations. TUNING +/- buttons Scan all the available radio stations. MEMORY button Press to memorize a preset station. SHIFT button Selects a memory page for preset stations. FM MODE button If "STEREO" flashes in the display and the FM stereo reception is poor, press this button. You will not have the stereo effect but the sound is improved. FM button Selects the FM band. AM button Selects the AM band. 5 MULTI CHANNEL DECODING indicator This indicator lights up when the unit is decoding signals recorded in a multi channel format. qd qs qa 0 6 Use the CINEMA STUDIO EX buttons to enjoy the CINEMA STUDIO EX sound effects. A/B/C buttons Press to activate the CINEMA STUDIO EX A, B or C sound field (page 27). 7 Use the SOUND FIELD buttons to enjoy surround sound. For details, see "Enjoying Surround Sound" starting from page 25. A.F.D. button / indicator Press to set the receiver to automatically detect the type of audio signal being input and perform proper decoding (if necessary). MODE button / indicator Press to activate the sound field selection mode (page 26). 2CH button / indicator Press to output sound from only the front (left and right) speakers. 22 8 INPUT MODE button Press to select the input mode for your digital components (DVD/LD and TV/SAT). Each press switches the input mode of the currently selected component. Select AUTO qa MUTING button Press to mute the sound. MUTING appears in the display when the sound is muted. qs EQUALIZER button Press to turn the equalizer on or off. The EQ indicator in the display lights when the equalizer is turned on. When you adjust the equalizer using the EQ parameters (page 34) the settings are stored automatically and can be reproduced wherever you turn on the equalizer. * The equalizer is not compatible with 96 kHz digital audio signals and during MULTI CH IN input. To Give priority to digital signals when there are both digital and analog connections. If there are no digital signals, analog is selected Specify the digital audio signals input to the DIGITAL OPTICAL input jacks Specify the digital audio signals input to the DIGITAL COAXIAL input jacks (DVD/LD only) Specify the analog audio signals input to the AUDIO IN (L and R) jacks DIGITAL (OPTICAL) www..com DIGITAL (COAXIAL) Location of Parts and Basic Amplifier Operations z When you want to listen to an analog source without any digital processing Do the following to bypass the sound field and equalizer circuits. 1 Press 2CH. 2 Press EQ to turn off the EQ indicator. The result will be a sound that is highly faithful to the program source. ANALOG Note If 96 kHz digital signal is input, the EQ, sound field and surround parameters do not function. 9 Function buttons Press one of the buttons to select the component you want to use. To select VCR DVD or LD player TV or satellite tuner MD or Tape deck CD player Built in tuner An audio component qd MULTI CH IN button Press to enjoy the audio source connected to the MULTI CH IN jacks with the video from the selected component. Press again to cancel MULTI CH IN. * When the MULTI CH IN is selected, equalizer, and sound field effects do not function. Press VIDEO DVD/LD TV/SAT MD/TAPE CD TUNER AUX qf SPEAKERS button Press SPEAKERS button to ON. PHONES jack Connects headphones. * When you connect the headphones, no sound will come from the speakers. After selecting the component, turn on the component you selected and play the program source. * After selecting VCR, DVD player, or LD player, turn on the TV and set the TV's video input to match the component you selected. 0 MASTER VOLUME control After turning on the component you selected, rotate to adjust the volume. 23 Front Panel Parts Description qg qh qj qk ql MULTI CHANNEL DECODING VIDEO DVD/LD TV/SAT ?/1 MD/TAPE INPUT MODE MASTER VOLUME CD TUNER AUX + SPEAKERS DISPLAY PRESET TUNING EQ LEVEL SURR SET UP NAME A CINEMA STUDIO EX B SOUND FIELD A.F.D. ENTER MODE 2CH C MULTI CH IN MUTING EQUALIZER - DIMMER - + - TUNING + www..com PHONES Location of Parts and Basic Amplifier Operations MEMORY SHIFT FM MODE FM AM ws qg EQ button Press to activate the equalizer parameters (page 34). The indicator on the button lights up and you can adjust the various equalizer parameters. qh SURR button Press to activate the surround parameters (page 32). The indicator on the button lights up and you can adjust the various surround parameters (effect level, wall type, etc.). qj LEVEL button Press to activate the speaker level parameters (page 33). The indicator on the button lights up and you can adjust the various speaker level parameters (front balance, surround balance, etc.). qk SET UP button Press to activate the setup mode, then use the cursor buttons (wa) to select any of the following indications. You can then make various settings using the jog dial (ws). When you select Speaker type Speaker setup wa w; When you select Speaker Distance You can Specify the front, center, and surround speaker distances. (page 17) MULTI CH IN video input Specify the video input to be used with the audio signals from the MULTI CH IN jacks. (page 43) Dimmer range Specify the display to turn off when you press the DIMMER button several times. (page 43) ql NAME button Press to activate the name function and enter names for preset stations and program sources (page 41). w; ENTER button Press to enter individual characters for the preset station and program source names. wa Cursor buttons ( / ) Press to select various speaker level, surround, and equalizer parameters (etc.). ws Jog dial Turn to adjust the selected speaker level, surround, and equalizer parameters (etc.). You can Specify the type of speakers. (page 15) Specify the front, center, surround speaker sizes, the surround speaker position, and whether or not you are using a sub woofer. (page 15) 24 Enjoying Surround Sound This chapter describes how to set up the receiver to enjoy surround sound. You can enjoy multi channel surround when playing back software encoded www..com with Dolby Digital or DTS. You can take advantage of surround sound simply by selecting one of the receiver's pre-programmed sound modes. They bring the exciting and powerful sound of movie theaters and concert halls into your home. You can also customize the sound modes to obtain the sound you desire by changing the various surround parameters. The receiver contains a variety of different sound modes. The cinema sound modes are designed for use when playing back movie software (DVD, LD, etc.) encoded with multi channel surround sound or Dolby Pro Logic. In addition to decoding the surround sound, some of these modes also provide sound effects commonly found in movie theaters. The virtual sound modes contain compelling applications of the Sony Digital Cinema Sound digital signal processing technology. They shift the sound away from the actual speaker locations to simulate the presence of several "virtual" speakers. The music (etc.) sound modes are designed for use with standard audio sources and TV broadcasts. They add reverberation to the source signal to make you feel as if you were in a concert hall or stadium (etc.). Use these sound modes with two-channel sources like CD and stereo broadcasts of sports programs or musical concerts. For more information about the sound modes, see pages 27 - 29. A.F.D. The "Auto Format Decoding" sound mode presents the sound exactly as it was encoded, without adding any reverberation (etc.). To fully enjoy surround sound, you must register the number and location of your speakers. See "MultiChannel Surround setup" starting on page 15 to set the speaker parameters before enjoying surround sound. Enjoying Surround Sound 25 Selecting a Sound Field EQ LEVEL SOUND FIELD buttons SURR You can enjoy surround sound simply by selecting one of the pre-programmed sound fields according to the program you want to listen to. MULTI CHANNEL DECODING VIDEO DVD/LD TV/SAT ?/1 MD/TAPE INPUT MODE MASTER VOLUME CD TUNER AUX 1 2 + Press MODE. The current sound field is indicated in the display. Turn the jog dial or press the cursor buttons ( or ) to select the sound field you want. See the table starting on page 27 for information on each sound field. SPEAKERS DISPLAY PRESET TUNING EQ LEVEL SURR SET UP NAME A CINEMA STUDIO EX B SOUND FIELD A.F.D. ENTER MODE 2CH C MULTI CH IN MUTING EQUALIZER - DIMMER - + - TUNING + MEMORY PHONES SHIFT FM MODE FM AM Cursor buttons www..com Jog dial EQUALIZER To turn the sound field off Press A.F.D. or 2CH (page 22). Brief descriptions of buttons used to enjoy surround sound LEVEL button: Press to customize the level parameters. SURR button: Press to customize the surround parameters in the current sound field. EQ button: Press to customize the equalizer parameters in the current sound field. Cursor buttons ( / ): Use to select parameters after pressing the LEVEL, SURR, EQ or SET UP buttons. Jog dial: Use to adjust parameters and select sound fields (etc.). SOUND FIELD buttons: A.F.D. button: Press to set the receiver to automatically detect the type of audio signal being input and perform proper decoding (if necessary). MODE button: Press to activate the sound field selection mode. 2CH button: Press to output sound from only the front (left and right) speakers. EQUALIZER button: Turns the equalizer effect on or off. z The receiver memorizes the last sound field selected for each program source (Sound Field Link) Whenever you select a program source, the sound field that was last applied is automatically applied again. For example, if you listen to CD with SMALL HALL as the sound field, change to a different program source, then return to CD, SMALL HALL will be applied again. With the tuner, sound fields are memorized separately for AM, FM, and all preset stations. Enjoying Surround Sound z You can identify Dolby Surround-encoded software by looking at the packaging Dolby Digital discs are labeled with the logo, and Dolby Surround encoded programs are labeled with the A logo. 26 Sound field information Sound field NORM. SURR. (NORMAL SURROUND) Effect Software with multi channel surround audio signals is played according to the way it was recorded. Software with two channel audio signals, is decoded with Dolby Pro Logic to create surround effects. Reproduces the sound characteristics of Sony Pictures Entertainment's classic editing studio by using the 3D sound imaging of V.M.DIMENS. (page 28) to create 5 sets of virtual speakers surrounding the listener from a single pair of actual surround speakers. Reproduces the sound characteristics of Sony Pictures Entertainment's mixing studio which is one of the most up-to-date facilities in Hollywood. The 3D sound imaging of V.M.DIMENS. (page 28) is used to create 5 sets of virtual speakers surrounding the listener from a single pair of actual surround speakers. Reproduces the sound characteristics of Sony Pictures Entertainment's BGM recording studio by using the 3D sound imaging of V.M.DIMENS. (page 28) to create 5 sets of virtual speakers surrounding the listener from a single pair of actual surround speakers. Notes C. ST. EX A (CINEMA STUDIO EX. A)1)2) (Press CINEMA STUDIO EX. A button) www..com C. ST. EX B (CINEMA STUDIO EX. B)1)2) (Press CINEMA STUDIO EX. B button) This is a standard mode, great for watching most any type of movie. This mode is ideal for watching sciencefiction or action movies with lots of sound effects. Enjoying Surround Sound C. ST. EX C (CINEMA STUDIO EX. C)1)2) (Press CINEMA STUDIO EX. C button) This mode is ideal for watching musicals or classic films where music is featured in the soundtrack. Reproduces the sound characteristics of Sony Pictures S. C. EX A (SEMI CINEMA STUDIO EX. A)1) Entertainment's classic editing studio using the 3D sound imaging of V. SEMI M.D. (page 28) to create 5 set of virtual speakers surrounding the listener from the sound of the front speakers (without using actual surround speakers). S. C. EX B (SEMI CINEMA STUDIO EX. B)1) Reproduces the sound characteristics of Sony Pictures Entertainment's mixing studio which is one of the most up-to-date facilities in Hollywood. The 3D sound imaging of V. SEMI M.D. (page 28) is used to create 5 sets of virtual speakers surrounding the listener from the sound of the front speakers (without using actual surround speakers). Reproduces the sound characteristics of Sony Pictures Entertainment's BGM recording studio using the 3D sound imaging of V. SEMI M.D. (page 28) to create 5 sets of virtual speakers surrounding the listener from the sound of the front speakers (without using actual surround speakers). L C R LS RS LS LS RS RS S. C. EX C (SEMI CINEMA STUDIO EX. C)1) 1) 2) "VIRTUAL" sound field: Sound field with virtual speakers. You can select by pressing the buttons on the front panel. 27 Selecting a Sound Field Sound field information Sound field V.M.DIMENS. (VIRTUAL MULTI DIMENSION) 1) Effect Uses 3D sound imaging to create an array of virtual surround speakers positioned higher than the listener from a single pair of actual surround speakers. This mode creates four sets of virtual speakers surrounding the listener at approximately a 30 angle of elevation. Notes L C R SIDE** SL SR LS LS RS RS L C R www..com MIDDLE** LS RS SL LS RS SR Enjoying Surround Sound L C R BEHIND** LS RS LS SL SR RS ** See page 16 V. SEMI M.D.1) (VIRTUAL SEMI-MULTI DIMENSION) Uses 3D sound imaging to create virtual surround speakers from the sound of the front speakers without using actual surround speakers. This mode creates five sets of virtual speakers surrounding the listener at a 30 angle of elevation. L C R LS RS LS LS RS RS S. HALL (SMALL HALL) L. HALL (LARGE HALL) JAZZ (JAZZ CLUB) L. HOUSE (LIVE HOUSE) GAME Reproduces the acoustics of a small rectangular concert hall. Reproduces the acoustics of a large rectangular concert hall. Reproduces the acoustics of a jazz club. Reproduces the acoustics of a 300-seat live house. Obtains maximum audio impact from video game software. Ideal for musicals and opera. Great for rock or pop music. Be sure to set the game machine to stereo mode when using game software with stereo sound capabilities. 1) "VIRTUAL" sound field: Sound field with virtual speakers. Notes * When you select S. HALL, L. HALL, JAZZ and L. HOUSE, no sound is output from the sub woofer if you select NORM. SP. and your front speaker size is set to "LARGE". However, sound will be output from the sub woofer if the digital input signal contains L.F.E. signals. * The effects provided by the virtual speakers may cause increased noise in the play back signal. * When listening to sound fields that employ the virtual speakers, you will not be able to hear any sound coming directly from the surround speakers. 28 Use the buttons on the front panel to operate the following modes A.F.D. AUTO FORMAT DECODING (Press the A.F.D. button) Automatically detects the type of audio signal being input (Dolby Digital, Dolby Pro Logic, or standard two channel stereo) and performs the proper decoding if necessary. This mode presents the sound as it was recorded/encoded, without adding any effects. Outputs the sound from the front left and right speakers only. Standard two channel (stereo) sources completely bypass the sound field processing. Multi channel surround formats are downmixed to two channels. You can use this mode as a reference. Set the EQUALIZER to OFF while using this mode to hear the source sound exactly as it was recorded. 2CH ST. 2 CHANNEL (Press the 2CH button) This allows you to play any source using only the front left and right speakers. Notes www..com * No sound is output from the sub woofer when the 2 CHANNEL mode is selected. To listen to two channel (stereo) sources using the front left and right speakers and a sub woofer, use the AUTO FORMAT DECODING mode. * When you select "Micro Satellite Speaker", internal sound processor will automatically redirect bass sound to subwoofer. If you want to listen to two channel (stereo) sources under this setting, we recommend that you choose AUTO FORMAT DECODING mode so that you can take advantage of your subwoofer to get back correct bass signal. Enjoying Surround Sound 29 Understanding the Multi-Channel Surround Displays qs qd 1 2 3 4 5 a DIGITAL PRO LOGIC DTS MPEG STEREO MONO SW SP. OFF OPT COAX D.RANGE EQ LCR LFE SL S SR MEMORY 9 qa 8 7 6 0 1 ; DIGITAL This indicator lights up when the receiver is decoding www..com signals recorded in the Dolby Digital format. 2 PRO LOGIC Lights up when the receiver applies Pro Logic processing to two channel signals in order to output the center and surround channel signals.* * However, this indicator does not light if the center and surround speakers are set to "NO", or the SPEAKERS button is set to OFF and the A.F.D. or NORMAL SURROUND sound fields are selected. 8 COAX Lights up when the source signal is a digital signal being input through the COAX terminal. 9 OPT Lights up when the source signal is a digital signal being input through the OPT terminal. 0 Play back channel indicators The letters light up to indicate the channels being played back. L: Front Left R: Front Right C: Center (monaural) SL: Left Surround SR: Right Surround S: Surround (monaural or the surround components obtained by Pro Logic processing) The boxes around the letters light up to indicate the speakers used to playback the channels. See the next page for details regarding the playback channel indicators. qa LFE LFE will light up when the disc being played contains the LFE (Low Frequency Effect) channel and when the sound of the LFE channel signal is actually being reproduced. Enjoying Surround Sound 3 DTS Lights up when DTS signals are input. Note When playing a DTS format disc, be sure that you have made digital connections and that INPUT MODE is NOT set to ANALOG (see 8 on page 23). 4 MPEG Lights up when MPEG** signals are input. ** Supports MPEG 2 channel only. 5 Tuner indicators These indicators light up when using the receiver to tune in radio stations, etc. See pages 36 - 39 for tuner operations. 6 EQ Lights when the equalizer functions. 7 D. RANGE Lights up when dynamic range compression is active. See page 34 to adjust the dynamic range compression. qs SW Lights up when sub woofer selection is set to "YES" (page 17) and the audio signal is output from the SUB WOOFER jack. qd SP. OFF Lights up when headphone is inserted or the SPEAKERS button is set to OFF. 30 Source sound displays The letters (L, C, R, etc.) indicate the source sound. The box around the letters varies to show how the receiver downmixes the source sound (based on the speakers settings). When using music sound modes such as SMALL HALL or JAZZ CLUB, the receiver adds reverberation based on the source sound. The following table shows how the indicators light up when using AUTO FORMAT DECODING mode. Although the table below shows almost all of the configurations available from multi channel surround signals, the ones marked " " are the most common. Recording Format (Front/ Surround) www..com Source sound and Output Channel Display Input Channel Display All speakers present Surround speakers absent a DIGITAL C Center speaker absent a DIGITAL C Surround/center speakers absent a DIGITAL C DOLBY DIGITAL [1/0] 1/0 DTS [1/0] DOLBY DIGITAL [2/0] 2/0* DTS [2/0] DOLBY DIGITAL [3/0] 3/0 DTS [3/0] DOLBY DIGITAL [2/1] 2/1 DTS [2/1] DOLBY DIGITAL [3/1] 3/1 DTS [3/1] DOLBY DIGITAL [2/2] 2/2 DTS [2/2] DOLBY DIGITAL [3/2] 3/2 DTS [3/2] 2/0** DOLBY DIGITAL [2/0] DOLBY PROLOGIC PCM XX kHz*** * Signals with Dolby Surround encoded flag OFF ** Signals with Dolby Surround encoded flag ON *** The sampling rate is displayed. a DIGITAL C C C C C dts dts L R dts L R dts L R Enjoying Surround Sound a DIGITAL a DIGITAL a DIGITAL a DIGITAL L R L R L R L R L R dts dts L C R dts L C R dts L C R a DIGITAL a DIGITAL a DIGITAL a DIGITAL L C R L C R L C R L C R L C R dts dts L S L R S L C S C S R L R dts L S R S L C S C S R L R dts L S R S L C S C S R L R a DIGITAL a DIGITAL a DIGITAL a DIGITAL L S R R S dts dts dts dts a DIGITAL a DIGITAL a DIGITAL a DIGITAL L C S C S R L R L R L R L R dts dts R SR R SR dts R SR R SR dts R SR R SR a DIGITAL L SL L SL a DIGITAL L SL L SL a DIGITAL L SL L SL a DIGITAL L SL L SL R SR R SR dts dts dts dts a DIGITAL LCR SL SR LCR SL SR L C S R a DIGITAL LCR SL SR LCR SL SR L C S R a DIGITAL LCR SL SR LCR SL SR L C S R a DIGITAL LCR SL SR LCR SL SR L C S R dts dts dts dts a DIGITAL PRO LOGIC a DIGITAL PRO LOGIC a DIGITAL PRO LOGIC a DIGITAL PRO LOGIC L PRO LOGIC C S R PRO LOGIC L C S R PRO LOGIC L C S R PRO LOGIC L C S R L R L R L R L R Notes * The receiver performs Pro Logic decoding and the display conforms to 2/0** when using the following movie sound modes with 2/0* or STEREO PCM format signals. (C. ST. EX A, B, C, S. C. EX A, B, C, V.M.DIMENS. and V. SEMI M.D.) * When using music sound modes such as SMALL HALL or JAZZ CLUB with standard audio formats e.g., PCM, the receiver creates surround signals from the front L and R signals. In this case, sound is output from the surround speakers, but output channel indicators for the surround speakers do not light. 31 Customizing Sound Fields By adjusting the surround parameters and the tone characteristics of the front speakers, you can customize the sound fields to suit your particular listening situation. Once you customize a sound field, the changes are stored in memory indefinitely (unless the receiver is unplugged for about one week). You can change a customized sound field any time by making new adjustments to the parameters. See the table on page 35 for the parameters available in each sound field. www..com Wall type Initial setting : WALL MID When sound is reflected off soft material, such as a curtain, the high frequency elements are reduced. A hard wall is highly reflective and does not significantly affect the frequency response of the reflected sound. This parameter lets you control the level of the high frequencies to alter the sonic character of your listening environment by simulating a softer (S) or harder (H) wall. * The wall type can be adjusted from WALL S. 1 ~ WALL S. 8 (soft) to WALL H. 1 ~ WALL H. 8 (hard) in 17 steps. * The midpoint WALL MID designates a neutral wall (made of wood). Reverberation Initial setting : REVB. MID Before sound reaches our ears, it is reflected (reverberated) many times between the left and right walls, ceiling, and floor. In a large room, sound takes more time to bounce from one surface to another than in a smaller room. This parameter lets you control the spacing of the early reflections to simulate a sonically larger (L) or smaller (S) room. * The reverberation can be adjusted from REVB. S. 1 ~ REVB. S. 8 (short) to REVB. L. 1 ~ REVB. L. 8 (long) in 17 steps. * The midpoint REVB. MID designates a standard room with no adjustment. Screen depth Initial setting : SCR. MID In a movie theater, sound seems to come from inside the image reflected on the movie screen. This parameter allows you to create the same sensation in your listening room by shifting the sound of the front speakers "into" the screen. * The screen depth can be set to SCR. OFF, SCR. MID, or SCR. DEEP. * SCR. DEEP provides the greatest amount of screen depth. To get the most from multi channel surround sound Position your speakers and do the procedures described in "Multi Channel Surround Setup" starting on page 15 before you customize a sound field. Enjoying Surround Sound Adjusting the surround parameters The SURR menu contains parameters that let you customize various aspects of the current sound field. The settings available in this menu are stored individually for each sound field. 1 2 Start playing a program source encoded with multi channel surround sound. Press SURR. The button lights up and the first parameter is displayed. Press the cursor buttons ( or parameter you want to adjust. ) to select the 3 4 Turn the jog dial to select the setting you want. The setting is stored automatically. Effect level (EFFECT) Initial setting : (depends on sound mode) This parameter lets you adjust the "presence" of the current surround effect. 32 Adjusting the level parameters The LEVEL menu contains parameters that let you adjust the balance and speaker volumes of each speaker. The settings available in this menu are applied to all sound fields. *Sub woofer level Initial setting : S.W. 0 dB Lets you adjust the level of the sub woofer. * The level can be adjusted in 1 dB steps from -6 dB to +6 dB. * The parameters can be adjusted separately for MULTI CH IN. 1 2 Start playing a program source encoded with multi channel surround sound. Press LEVEL. The button lights up and the first parameter is displayed. www..com 3 4 Press the cursor buttons ( or parameter you want to adjust. ) to select the Turn the jog dial to select the setting you want. The setting is stored automatically. R) *Front balance ( L Initial setting : BALANCE Lets you adjust the balance between the front left and right speakers. * The balance can be adjusted 8 steps. * These settings can also be adjusted using the supplied remote. See "Adjusting the speaker volume" (page 18). Low Frequency Effect Initial setting : L.F.E. 0 dB This parameter lets you attenuate the level of the LFE (Low Frequency Effect) channel output from the sub woofer without affecting the level of the bass frequencies sent to the sub woofer from the front, center or surround channels via the bass redirection circuitry. * The level can be adjusted in 1 dB steps from -20.0 dB to 0 dB (line level). 0 dB outputs the full LFE signal at the mix level determined by the recording engineer. * Selecting OFF mutes the sound of the LFE channel from the sub woofer. However, the low frequency sounds of the front, center, or surround speakers are output from the sub woofer according to the settings made for each speaker in the speaker setup (page 15). Enjoying Surround Sound *Surround balance ( SL SR ) Initial setting : BALANCE Lets you adjust the balance between the surround left and right speakers. * The balance can be adjusted 8 steps. * These settings can also be adjusted using the supplied remote. See "Adjusting the speaker volume" (page 18). *Center level Initial setting : CTR 0 dB Lets you adjust the level of the center speaker. * The level can be adjusted in 1 dB steps from -6 dB to +6 dB. *Surround level Initial setting : SURR 0 dB Lets you adjust level of the surround (left and right) speakers. * The level can be adjusted in 1 dB steps from -6 dB to +6 dB. 33 Customizing Sound Fields Dynamic range compressor ( D. RANGE ) Initial setting : COMP. OFF Lets you compress the dynamic range of the sound track. This may be useful when you want to watch movies at low volumes late at night. * COMP. OFF reproduces the sound track with no compression. * COMP. STD reproduces the sound track with the dynamic range intended by the recording engineer. * COMP. 0.1 ~ 0.9 allow you to compress the dynamic range in small steps to achieve the sound you want. * COMP. MAX provides a dramatic compression of the www..com dynamic range. Note Dynamic range compression does not work with DTS sources. Adjusting the equalizer The EQ menu lets you adjust the equalization (low and high frequencies) of the front speakers. The equalizer settings are stored individually for each sound field. 1 2 Start playing a program source encoded with multi channel surround sound. Press EQ. The button lights up and the first parameter is displayed. Press the cursor buttons ( or parameter you want to adjust. ) to select the 3 4 Enjoying Surround Sound z About the Dynamic Range Compressor This parameter allows you to compress the dynamic range of the soundtrack based on the dynamic range information included in the Dolby Digital signal. "COMP. STD" is standard compression, but because many sources have only light compression, you may not notice much difference when using COMP. 0.1~0.9. Therefore, we recommend using the "COMP. MAX" setting. This greatly compresses the dynamic range and allows you to view movies late at night at low volumes. Unlike analog limiters, the levels are predetermined and it provides a very natural compression. Turn the jog dial to select the setting you want. The setting is stored automatically. z You can turn off the equalization without erasing it The equalizer settings are stored separately for each sound field. Press the EQUALIZER button to turn the EQ indicator off. Front speaker bass adjustment (Level/Frequency) 1 Use the cursor buttons ( / ) to select the level (dB) or frequency (Hz). 2 Use the jog dial to adjust. Repeat until you achieve the sound you desire. * The level can be adjusted 6 dB in 1 dB steps. * The frequency can be adjusted from 99 Hz to 1.0 kHz in 21 steps. Front speaker treble adjustment (Level/ Frequency) Adjust as described in "Front speaker bass adjustment". * The level can be adjusted 6 dB in 1 dB steps. * The frequency can be adjusted from 1.0 kHz to 10 kHz in 23 steps. Resetting customized sound fields to the factory settings 1 2 If the power is on, press ?/1 to turn off the power. Hold down MODE and press ?/1. "SF. CLR" appears in the display and all sound fields are reset at once. 34 Adjustable parameters for each sound field EFFECT LEVEL 2CH A.F.D. NORMAL SURROUND CINEMA STUDIO EX. A CINEMA STUDIO EX. B CINEMA STUDIO EX. C www..com SEMI CINEMA STUDIO EX. A SEMI CINEMA STUDIO EX. B SEMI CINEMA STUDIO EX. C V. MULTI DIMENSION V. SEMI-M. DIMENSION SMALL HALL LARGE HALL JAZZ CLUB LIVE HOUSE GAME MULTI CH IN r r r r r r r r r r r r r r r r r r r r r r r r r r r WALL TYPE REVERB TIME SCREEN DEPTH FRONT BAL. r r r r r r r r r r r r r r r r r SURR BAL. CENTER SURR LEVEL LEVEL SUB WOOFER LFE LEVEL MIX r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r Enjoying Surround Sound r r r r r r r r r r r r r r r r r r r r r r r r r r r r r r D.RANGE COMP. 2CH A.F.D. NORMAL SURROUND CINEMA STUDIO EX. A CINEMA STUDIO EX. B CINEMA STUDIO EX. C SEMI CINEMA STUDIO EX. A SEMI CINEMA STUDIO EX. B SEMI CINEMA STUDIO EX. C V. MULTI DIMENSION V. SEMI-M. DIMENSION SMALL HALL LARGE HALL JAZZ CLUB LIVE HOUSE GAME MULTI CH IN r r r r r r r r r r r r r r r r EQ r r r r r r r r r r r r r r r r 35 Receiving Broadcasts This chapter describes how to receive FM or AM broadcasts and how to preset selected stations. You can tune in stations on this receiver in the following ways: Direct Tuning You can enter a frequency of the station you want directly by using the numeric buttons on the remote (see page 38). Automatic Tuning If you don't know the frequency of the station you want, you can let the receiver scan all available stations in your area (see page 38). Preset Tuning After you have tuned in stations using Direct Tuning or Automatic Tuning, you can preset them to the receiver (see page 39). Then you can tune in any of the stations directly by entering its 2-character code (see page 39). Up to 30 FM or AM stations can be preset. The receiver will also scan all the stations that you have preset (see page 39). Before you begin, make sure you have: * Connected an FM and AM antenna to the receiver (see page 5). www..com 36 PRESET TUNING +/- MEMORY TUNING +/- TUNER Brief descriptions of buttons used to receive broadcasts PRESET TUNING +/-: Press to scan all preset radio stations. TUNING +/-: Press to scan all available radio stations. FM MODE: If "STEREO" flashes in the display and the FM stereo reception is poor, press this button to improve the sound. You will not be able to enjoy stereo effect but the sound will be less distorted. Note MULTI CHANNEL DECODING VIDEO DVD/LD TV/SAT ?/1 MD/TAPE INPUT MODE MASTER VOLUME CD TUNER AUX + SPEAKERS DISPLAY PRESET TUNING EQ LEVEL SURR SET UP NAME A CINEMA STUDIO EX B SOUND FIELD A.F.D. ENTER MODE 2CH C MULTI CH IN MUTING EQUALIZER - DIMMER - + - TUNING + MEMORY PHONES SHIFT FM MODE FM AM FM www..com SHIFT AM FM MODE SLEEP AV ?/1 SYSTEM STANDBY ?/1 If "STEREO" does not appear at all even when the FM broadcast is received normally, press this button to turn on the "STEREO" indication. FUNCTION VIDEO 1 VIDEO 2 VIDEO 3 VIDEO DVD/LD TV/SAT PHONO MD/TAPE FN SHIFT FM: Press to select the FM band. Receiving Broadcasts AUX CD/SACD F TUNER AM: Press to select the AM band. Numeric buttons 1 4 MENU 2 ENTER 3 g G 5 TITLE 6 f MEMORY: Uses for memorizing preset stations. SHIFT: Press to select a memory page (A, B, or C) for presetting radio stations or tuning to preset stations. TUNER: Press to select the tuner. On the remote: D. TUNING: Press this button to enter a frequency directly using the numeric buttons. Numeric buttons: Press to enter a numeric value when inputting the frequency directly, presetting radio stations, or tuning to preset stations. 7 SHIFT 8 0 SWAP 9 RETURN >10 - /- - ENTER D.TUNING D.TUNING POSITION = 0 DISPLAY + D.SKIP/ CH/PRESET ANT TV/VTR - SUB CH + ) P IN P 9 JUMP ( WIDE DISC TV/ VIDEO P p MULTI CH/ 2 CH DIRECT SOUND FIELD 2CH/OFF A.F.D. - MODE + MUTING MASTER TEST TONE MAIN MENU VOL MENU 37 Direct Tuning For details on the buttons used in this section, see "Brief descriptions of buttons used to receive broadcasts" on page 37. Automatic Tuning For details on the buttons used in this section, see "Brief descriptions of buttons used to receive broadcasts" on page 37. 1 2 3 4 Press TUNER. The last received station is tuned in. Press FM or AM to select the FM or AM band. Press D.TUNING on the remote. Press the numeric buttons on the remote to enter 1 2 3 Press TUNER. The last received station is tuned in. Press FM or AM to select the FM or AM band. Press TUNING + or TUNING -. Press the + button to scan from low to high; press the - button to scan from high to low. When the receiver reaches either end of the band Scanning is repeated in the same direction. The receiver stops scanning whenever a station is received. www..com frequency. the Example 1: FM 102.50 MHz 1 b 0 b 2 b 5 b 0 Example 2: AM 1350 kHz (You don't have to enter the last "0" when the tuning interval is set to 10 kHz) 1 b 3 b 5 b 0 4 To continue scanning, press TUNING + or TUNING - again. Receiving Broadcasts If you cannot tune in a station and the entered numbers flash Make sure you've entered the right frequency. If not, repeat Steps 3 and 4. If the entered numbers still flash, the frequency is not used in your area. 5 If you've tuned in an AM station, adjust the direction of the AM loop antenna for optimum reception. Repeat Steps 2 to 5 to receive other stations. 6 z If you try to enter a frequency not covered by the tuning interval The entered value is automatically rounded up or down. Tuning intervals for direct tuning are: FM: 50 kHz AM: 10 kHz (to change to 9 kHz, see page 47.) 38 Preset Tuning For details on the buttons used in this section, see "Brief descriptions of buttons used to receive broadcasts" on page 37. Before tuning to preset stations, be sure to preset them by performing steps on "Presetting radio stations" below. Tuning to preset stations You can tune the preset stations either of the following two ways. Scanning the preset stations Presetting radio stations 1 2 Press TUNER. The last received stations is tuned in. Press PRESET TUNING + or PRESET TUNING - repeatedly to select the preset station you want. Each time you press the button, the receiver tunes in one preset station at a time , in the corresponding order and direction as follows: nA1A2...A0B1B2...B0N nC0...C2C1N 1 2 3 Press TUNER. The last received station is tuned in. Tune in the station that you want to preset using Direct Tuning or Automatic Tuning (page 39). Press MEMORY. "MEMORY" appears in the display for a few seconds. Do Steps 4 to 6 before "MEMORY" goes out. Press SHIFT to select a memory page (A, B or C). Each time you press SHIFT, the letter "A", "B" or "C" appears in the display. Select a preset number by pressing PRESET TUNING + or PRESET TUNING -. If "MEMORY" goes out before you press the preset number, start again from Step 3. Press MEMORY again to store the station. If "MEMORY" goes out before you can store the station, start again from Step 3. Repeat Steps 2 to 6 to preset another station. www..com 4 Using the preset codes Receiving Broadcasts 1 2 Press TUNER. The last received stations is turned in. Press SHIFT to select a memory page (A, B or C), then press the preset number of the station you want using the numeric buttons on the supplied remote. 5 6 7 To change a preset number to another station Do Steps 1 to 6 to preset the new station to the number. Note If the AC power cord is disconnected for about one week, all the preset stations will be cleared from the receiver's memory, and you will have to preset the stations again. 39 Other Operations Cursor buttons NAME SET UP MULTI CHANNEL DECODING VIDEO TUNER DVD/LD TV/SAT ?/1 MD/TAPE INPUT MODE MASTER VOLUME CD TUNER AUX + SPEAKERS DISPLAY PRESET TUNING EQ LEVEL SURR SET UP NAME A CINEMA STUDIO EX B SOUND FIELD A.F.D. ENTER MODE 2CH C MULTI CH IN MUTING EQUALIZER - DIMMER - + - TUNING + MEMORY PHONES SHIFT FM MODE FM AM Jog dial ENTER Brief descriptions of buttons that appear in this chapter www..com NAME button: Press to name preset stations or program sources. Jog dial: Use to select characters when naming preset stations or program sources. Cursor buttons ( / ): Use to move the cursor when naming preset stations or program sources. TUNER button: Press to select the tuner. SET UP button: Press to enter the set up mode. ENTER button: Press to enter the completed name of the preset station or program source. 40 Naming Preset Stations and Program Sources You can enter a name (index name) of up to 8 characters for preset stations and program sources. These names (for example, "VHS") appear in the receiver's display when a station or program source is selected. Note that no more than one name can be entered for each preset station or program source. This function is useful for distinguishing components of the same kind. For example, two VCRs can be specified as "VHS" and "8MM", respectively. It is also handy for identifying components connected to jacks meant for another type of component, for example, a second CD www..com player connected to the MD/TAPE jacks. Recording Your receiver makes it easy to record to and from the components connected to it. You don't have to connect the playback and recording components directly to each other: once you select a program source on the receiver, you can record and edit as you normally would using the controls on each component. Before you begin, make sure you've connected all components properly. Function buttons MULTI CHANNEL DECODING VIDEO DVD/LD TV/SAT ?/1 MD/TAPE INPUT MODE MASTER VOLUME CD TUNER AUX + 1 To name a preset station Press TUNER. The last station you received is tuned in. To name a program source Select the program source (component) to be named, then go to Step 3. SPEAKERS DISPLAY PRESET TUNING EQ LEVEL SURR SET UP NAME A CINEMA STUDIO EX B SOUND FIELD A.F.D. ENTER MODE 2CH C MULTI CH IN MUTING EQUALIZER - DIMMER - + - TUNING + MEMORY PHONES SHIFT FM MODE FM AM c c c c 2 Tune in the preset station you want to create an index name for. If you are not familiar with how to tune in preset stations, see "Tuning to preset stations" on page 39. Press NAME. Playback component (program source) Recording component (tape deck, MD deck, VCR) Other Operations c: Audio signal flow c: Video signal flow 3 4 Recording on an audio tape or MiniDisc Create an index name by using the jog dial and cursor buttons: Turn the jog dial to select a character, then press to move the cursor to the next position. To insert a space Turn the jog dial until a blank space appears in the display (you can find the space character between "] " and "A"). If you've made a mistake Press or repeatedly until the character to be changed flashes, then turn the jog dial to select the right character. You can record on a cassette tape or MiniDisc using the receiver. Refer to the instruction manual of your cassette deck or MD deck if you need help. 1 2 3 4 Select the component to be recorded. Prepare the component for playing. For example, insert a CD into the CD player. Insert a blank tape or MD into the recording deck and adjust the recording level, if necessary. Start recording on the recording deck, then start playback on the playback component. 5 Press ENTER. To assign index names to other stations Repeat Steps 2 to 5. 41 Recording Using the Sleep Timer You can set the receiver to turn off automatically at a specified time. Press SLEEP on the remote while the power is on. Each time you press SLEEP, the time changes as shown below. n 2-00-00 n 1-30-00n 1-00-00 n 0-30-00 n OFF Recording on a video tape You can record from a TV, or an LD player using the receiver. You can also add audio from a variety of audio sources when editing a video tape. See your LD player's instruction manual if you need help. 1 2 Select the program source to be recorded. Prepare the component for playing. For example, insert the laser disc you want to record into the LD player. Insert a blank video tape into the VCR for recording. Start recording on the recording VCR, then start playing the laser disc you want to record. The display dims after you have specified the time. z You can freely specify the time First, press SLEEP on the remote, then specify the time you want using the jog dial on the receiver. The sleep time changes in 1 minute intervals. You can specify up to 5 hours. www..com 3 4 z You can check the time remaining before the receiver turns off Press SLEEP on the remote. The remaining time appears in the display. z You can record the sound from any audio source onto a video tape while recording from a laser disc Locate the point where you want to start recording from another audio source, select the program source, then start playback. The audio from that source will be recorded onto the audio track of the video tape instead of the audio from the original medium. Other Operations To resume audio recording from the original medium, select the video source again. Notes * You cannot record a digital audio signal using a component connected to the analog MD/TAPE OUT or VIDEO OUT jacks. * Sound adjustments do not affect the signal output from the MD/TAPE OUT or VIDEO OUT jacks. * When MULTI CH IN is selected, audio signals are not output from MD/TAPE OUT or VIDEO OUT jacks. 42 Adjustment Using the SET UP Button The SET UP button allows you to make the following adjustments. Selecting the MULTI CH IN video input This parameter lets you specify the video input to be used with the audio signals from the MULTI CH IN jack. The MULTI CH IN video input is set to DVD/LD by default. 1 2 3 Press SET UP. Press the cursor buttons ( " MULTI CH IN VISUAL". or ) to select www..com Turn the jog dial to select the video input you want. Set the display to turn off This parameter lets you specify whether or not the display turns off when you press the DIMMER button several times. When "WIDE" is selected, you can set the display to turn off, but when "NARROW" is selected, you cannot set the display to turn off. The default setting is set to "NARROW". Other Operations 1 2 3 Press SET UP. Press the cursor buttons ( RANGE". or ) to select "DIM. Turn the jog dial to select "NARROW" or "WIDE". 43 Additional Information Troubleshooting If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help you remedy the problem. Also, see "Checking the connections" on page 19 to verify that the connections are correct. Should any problem persist, consult your nearest Sony dealer. There's no sound or only a very low-level sound is heard. , Check that the speakers and components are connected securely. , Make sure that you've selected the correct component on the receiver. , Check that the SPEAKERS button is not set to OFF. , Press MUTING if MUTING appears on the display. , The protective device on the receiver has been activated because of a short circuit. Turn off the receiver, eliminate the short-circuit problem and turn on the power again. The left and right sounds are unbalanced or reversed. , Check that the speakers and components are connected correctly and securely. , Adjust front balance parameter in the LEVEL menu. Severe hum or noise is heard. , Check that the speakers and components are connected securely. , Check that the connecting cords are away from a transformer or motor, and at least 10 feet (3 meters) away from a TV set or fluorescent light. , Move your TV away from the audio components. , The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol. No sound is heard from the center speaker. , Make sure the sound field function is on (press SOUND FIELD MODE). , Select the appropriate center mode (see pages 26 - 29). , Adjust the speaker volume (see page 18). , Make sure the center speaker size parameter is set to either SMALL or LARGE (see page 16). www..com 44 No sound or only a very low-level sound is heard from the surround speakers. , Make sure the sound field function is on (press SOUND FIELD MODE). , Select the appropriate center mode (see pages 26 - 29). , Adjust the speaker volume (see page 18). , Make sure the surround speaker size parameter is set to either SMALL or LARGE (see page 16). No sound is heard from the sub woofer. , Make sure the sub woofer is set to YES (see page www..com 17). , Check that 2CH mode has not been selected (see page 29). Recording cannot be done. , Check that the components are connected correctly. , Select the source component with a FUNCTION button. , When recording from a digital component, make sure the input mode is set to ANALOG (see page 23) before recording with a component connected to the analog MD/TAPE terminals. Radio stations cannot be tuned in. , Check that the antennas are connected securely. Adjust the antennas and connect an external antenna if necessary. , The signal strength of the stations is too weak (when tuning in with automatic tuning). Use direct tuning. , Make sure you set the tuning interval correctly (when tuning in AM stations with direct tuning) (see pages 38 and 47). , No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations). Preset the stations (see page 39). , Press DISPLAY so that the frequency appears in the display. The surround effect cannot be obtained. , Make sure the sound field function is on (press SOUND FIELD MODE). "PCM--kHz" appears on the display. , The sampling frequency is more than 48 kHz. Change the input player setting to 48 kHz. Nothing appears on the display. , When the display turns off immediately after the receiver is turned on, press DIMMER to change the display mode. No picture or an unclear picture appears on the TV screen or monitor. , Select the appropriate function on the receiver. , Set your TV to the appropriate input mode. , Move your TV away from the audio components. The remote does not function. , Point the remote at the remote sensor g on the receiver. , Remove any obstacles in the path between the remote and the receiver. , Replace both batteries in the remote with new ones, if they are weak. , Make sure you select the correct function on the remote. , If the remote is set to operate the TV only, use the remote to select a source or component other than TV before operating the receiver or other component. Additional Information Reference sections for clearing the receiver's memory To clear All memorized settings Customized sound fields See page 14 page 34 45 Specifications AUDIO POWER SPECIFICATIONS Frequency response MULTI CH IN, CD, MD/TAPE, DVD/ LD, TV/SAT, VIDEO, AUX: 10 Hz - 50 kHz +0.5/ -2 dB (with sound field and equalizer bypassed) Inputs (Analog) MULTI CH IN, CD, DVD/LD, MD/ TAPE, TV/SAT, VIDEO, AUX: Sensitivity: 250 mV Impedance: 50 kilohms S/Na): 96 dB (A, 250 mVb)) a) Input short. b) Weighted network, input level. Outputs POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 100 watts per channel minimum RMS power, with no more than www..com total harmonic 0.09% distortion from 250 milliwatts to rated output (USA model only). Amplifier section Rated Power Output at Stereo mode (8 ohms 20 Hz - 20 kHz, THD 0.09%) 100 W + 100 W Reference Power Output (8 ohms at 1 kHz, THD 0.7%) Front1): 100 W/ch Center1): 100 W Surround1): 100 W/ch 1) Depending on the sound field settings and sources, there may be no sound output. MD/TAPE, (OUT); VIDEO (AUDIO OUT): Voltage: 250 mV, Impedance: 10 kilohms SUB WOOFER: Voltage: 2 V Impedance: 1 kilohms PHONES: Accepts low- and high-impedance headphones 6 dB EQ Sampling Frequency 48 kHz (TV/SAT, MD/ TAPE OPTICAL IN) 96 kHz (DVD/LD OPTICAL IN, COAXIAL IN) Inputs (Digital) DVD/LD (coaxial): Sensitivity: - Impedance: 75 ohms S/N: 100 dB (A, 20 kHz LPF) DVD/LD, TV/SAT, (Optical): Sensitivity: - Impedance: - S/N: 100 dB (A, 20 kHz LPF) Additional Information 46 FM tuner section Tuning range 87.5 - 108.0 MHz Antenna terminals 75 ohms, unbalanced Intermediate frequency 10.7 MHz Sensitivity www..com AM tuner section Tuning range With 10-kHz tuning scale: 530 - 1710 kHzc) With 9-kHz tuning scale: 531 - 1710 kHzc) Antenna Loop antenna General System Tuner section: PLL quartz-locked digital synthesizer system Preamplifier section: Low-noise NF type equalizer Power amplifier section: Pure-complementary SEPP Mono: 18.3 dBf, 2.2 V/75 ohms Stereo: 38.3 dBf 22.5 V/75 ohms Intermediate frequency 450 kHz Usable sensitivity 50 dB/m (at 1,000 kHz or 999 kHz) S/N 54 dB (at 50 mV/m) Usable sensitivity 11.2 dBf, 1 V/75 ohms S/N Mono: 76 dB Stereo: 70 dB Power requirements 120 V AC, 60 Hz Power consumption Models of area code U: STR-DE575/K502: 220W In standby condition: 1W Models of area code CA: STR-DE575: 315 VA In standby condition: 1W Dimensions 430 x 296 x 157.5 mm (16 7/8 x 11 5/8 x 6 2/8 in.) including projecting parts and controls Harmonic distortion at 1 kHz Mono: 0.3% Stereo: 0.5% Separation 45 dB at 1 kHz Harmonic distortion 0.5 % (50 mV/m, 400 kHz) Selectivity At 9 kHz: 35 dB At 10 kHz: 40 dB Frequency response 30 Hz - 15 kHz +0.5/-2 dB Selectivity 60 dB at 400 kHz c) You can change the AM tuning interval to 9 kHz. After tuning in any AM station, turn off the receiver. Hold down the TUNING + button and press the ?/1 button. All preset stations will be erased when you change the tuning interval. To reset the scale to 10 kHz, repeat the procedure. Additional Information Mass (Approx.) Video section Inputs Video: 1 Vp-p 75 ohms S-video*: Y: 1 Vp-p 75 ohms C: 0.286 Vp-p 75 ohms Video: 1 Vp-p 75 ohms S-video*: Y: 1 Vp-p 75 ohms C: 0.286 Vp-p 75 ohms 7.4 kg (16 lbs. 6 oz.) Supplied accessories See page 4. For details on the area code of the component you are using, see page 3. Design and specifications are subject to change without notice. Outputs * STR-DE575 only 47 Glossary Surround sound Sound that consists of three elements: direct sound, early reflected sound (early reflections) and reverberative sound (reverberation). The acoustics of the surrounding space affect the way these three sound elements are heard. Surround sound combines these sound elements in such a way that you actually can sense the size of the venue, as well as its type. * Types www..comof sound Early reflections Reverberation Dolby Digital This sound format for movie theaters is more advanced than Dolby Pro Logic Surround. In this format, the surround speakers output stereo sound with an expanded frequency range and a sub woofer channel for deep bass is independently provided. This format is also called "5.1" because the sub woofer channel is counted as 0.1 channel (since it functions only when a deep bass effect is needed). All six channels in this format are recorded separately to realize superior channel separation. Furthermore, since all the signals are processed digitally, less signal degradation occurs. Digital Cinema Sound This is the generic name of the surround sound produced by digital signal processing technology developed by Sony. Unlike previous surround sound fields mainly directed at the reproduction of music, Digital Cinema Sound is designed specifically for the enjoyment of movies. Direct sound * Transition of sound from surround speakers Direct sound Level Early reflections Reverberation Additional Information Early reflection time Time Dolby Pro Logic Surround As one method of decoding Dolby Surround, Dolby Pro Logic Surround produces four channels from twochannel sound. Compared with the former Dolby Surround system, Dolby Pro Logic Surround reproduces left-to-right panning more naturally and localizes sounds more precisely. To take full advantage of Dolby Pro Logic Surround, you should have one pair of surround speakers and a center speaker. The surround speakers output monaural sound. 48 Settings Using SURR, LEVEL, EQ, and SET UP buttons You can make various settings using the LEVEL, SURR, EQ, SET UP buttons, cursor buttons and jog dial. The table below shows each of the settings that these buttons can make. Press and light SURR button Press or to select Turn jog dial to select depends on sound mode (in 16 steps) between -8 to +8 (in 1 increment steps) -8 to +8 (in 1 increment steps) SCR. OFF, SCR. MID or SCR. DEEP between -8 to +8 (in 1 increment steps) between -8 to +8 (in 1 increment steps) between -6 dB to +6 dB (in 1 dB steps) between -6 dB to +6 dB (in 1 dB steps) between -6 dB to +6 dB (in 1 dB steps) OFF, or -20 dB to 0 dB (in 1 dB steps) OFF, 0.1 to 0.9 (in 0.1 dB steps), STD, or MAX between -6 dB to +6 dB (in 1 dB steps) between 99 Hz and 1.0 kHz (in 21 steps) between -6 dB to +6 dB (in 1 dB steps) between 1.0 kHz and 10 kHz (in 23 steps) LARGE or SMALL LARGE, SMALL, or NO See page 32 EFFECT LEVEL WALL TYPE REVERBERATION TIME SCREEN DEPTH LEVEL button www..com FRONT BALANCE SURR BALANCE CENTER LEVEL SURR LEVEL SUB WOOFER LEVEL LFE MIX LEVEL DYNAMIC RANGE COMP 33 EQ button FRONT BASS GAIN FRONT BASS FREQUENCY FRONT TREBLE GAIN FRONT TREBLE FREQUENCY 34 *SET UP L R (FRONT) 15 C (CENTER) SL SR (SURR) S.W. (SUB WOOFER) L R Additional Information LARGE, SMALL, or NO S.W. YES or S.W. NO between 3 feet (1.0 meters) and 40 feet (12.0 meters) (in 1 foot (0.1 meter) steps) between FRONT and 5 feet (1.5 meters) (in 1 foot (0.1 meter) steps) between FRONT and 15 feet (4.5 meters) (in 1 foot (0.1 meter) steps) PL. SIDE, PL. MID. or PL. BEHD. HGT. LOW or HGT. HIGH V-VIDEO, V-DVD/LD, V-TV/SAT NARROW or WIDE 43 (FRONT) XX.X ft. C (CENTER) XX.X ft. (SURR) XX.X ft. (SURR) PL. XX.X (SURR) HGT. XX.X VISUAL XX.X SL SR SL SR SL SR MULTI CH IN DIM.RANGE * When you press the SET UP button, you can select NORM. SP. (for normal speakers) or MICRO SP. (for Micro Satellite speakers). (page 15) 49 Remote Button Description You can use the remote RM-U305 to operate the components in your system. The tables below show the settings of each button. Remote Button SLEEP Operations Receiver Function Activates the sleep function and the duration which the receiver turns off automatically. Turns the audio and video components on or off. Remote Button ENTER Operations TV/VCR/SAT/ Tape deck/ LD player/ VCD player/ MD deck/ DAT deck Receiver Function After selecting a channel, disc or track using the numeric buttons, press to enter the value. AV ?/1 www..com ?/1 VIDEO/ VIDEO 1 VIDEO 2 VIDEO 3 DVD/LD TV/SAT MD/TAPE CD/SACD TV/VCR/ CD player/ DVD player/ MD deck/ VCD player/ LD player/ DAT deck Receiver Receiver Receiver Receiver Receiver Receiver Receiver Receiver Receiver Receiver Receiver Remote Receiver SHIFT Press repeatedly to select a memory page for presetting radio stations or tuning to preset stations. Selects the channel entry mode, either one or two digit. Tuner station direct keyin mode. Turns the receiver on or off. To watch VCR. (VTR mode 3) To watch VCR. (VTR mode 1) To watch VCR. (VTR mode 2) To watch DVD or laser disc. To watch TV programs or satellite receiver. To listen to Minidisc or audio tape. To listen to compact disc. To listen to radio programs. To listen to turn table. To listen to an audio equipment. Use simultaneously to select other function. Use with "SHIFT" button to select tuner preset station numeric input during DIRECT TUNING or MEMORY mode. Selects track numbers. 0 selects track 10. -/-- TV D.TUNING ./> Receiver CD player/ Skips tracks. MD deck/ DVD player/ LD player/ VCD player/ Tape deck/VCR/ DAT deck CD player/ DVD player/ VCD player MD deck/ Tape deck/ VCR/ LD player/ DAT deck Searches tracks (forward or backward). Fastforwards or rewinds. m/M Additional Information TUNER PHONO AUX FN SHIFT* 0-9 n N Tape deck CD player/ MD deck/Tape deck/VCR/ DVD player/ VCD player/ LD player/ DAT deck Starts play on the reverse side. Starts play. CD player/ MD deck/ VCD player/ LD player/ DAT deck TV/VCR/SAT >10 CD player/ MD deck/ Tape deck/ LD player/ VCD player * VIDEO 1, VIDEO 2, VIDEO 3, PHONO and MD/TAPE function is a 2-key operation. To select the above function, press FN SHIFT (function shift) and the function key you want simultaneously. For example, press FN SHIFT and CD/SACD to select MD/TAPE function. Selects channel numbers. Selects tracks numbers over 10. Note When you press the function buttons (VIDEO, DVD/LD, TV/SAT), the input mode of the TV might not switch to the corresponding input mode that you want. In this case, press the TV/VIDEO button to switch the input mode of the TV. 50 Remote Button X Operations CD player/ MD deck/Tape deck/VCR/ DVD player/ VCD player/ LD player/ DAT deck CD player/ MD deck/Tape deck/VCR/ DVD player/ VCD player/ LD player/ DAT deck TV TV CD player TV Receiver TV/VCR/SAT CD player Function Pauses play or record. (Also starts recording with components in record standby.) Remote Button TEST TONE MAIN MENU Operations Receiver Receiver Function Press to output test tone. Press this button repeatedly to select one of the two cursor modes: LEVEL and SURROUND. Adjusts the master volume of the receiver. Selects a menu item. Makes adjustment or change the setting. Displays DVD menu. Selects a menu item. Enters the selection. Returns to the previous menu or exits the menu. Displays DVD title. x Stops play. MASTER VOL +/- MENU MENU +/- MENU F/f/G/g ENTER RETURN TITLE Receiver Receiver Receiver DVD player DVD player DVD player DVD player DVD player www..com POSITION** SWAP** DISC SUB CH +/-** D. SKIP/CH/ PRESET +/- Changes the position of the small picture. Swaps the small and the large picture. Select discs (Mega storage CD player only). Selects preset channels for the small picture. Scans and selects preset stations. Selects preset channels. Skips discs (CD player with multi-disc changer only). Selects information displayed on the TV screen. Activates the picture-inpicture function. Toggles between the previous and the current channels. Selects the wide picture mode. Selects output signal from the aerial terminal: TV signal or VCR program. Selects input signal: TV input or video input. Auto Format Decoding. Turns off sound field or selects 2CH mode. Selects sound field mode. Selects MULTI CH IN source. Mutes the sound from the receiver. ** Only for Sony TVs with the picture-in-picture function. Notes * Some functions explained in this section may not work depending on the model of the receiver. * The above explanation is intended to serve as an example only. Therefore, depending on the component the above operation may not be possible or may operate differently than described. * The VIDEO 1, VIDEO 2, VIDEO 3 and PHONO functions are not available for set operation. DISPLAY TV/VCR/ LD player/ DVD player/ VCD player TV TV Additional Information P IN P** JUMP WIDE ANT TV/VTR TV VCR TV/VIDEO A. F. D. 2CH/OFF MODE +/- MULTI CH/ 2 CH DIRECT MUTING TV/VCR Receiver Receiver Receiver Receiver Receiver 51 Remote Button Description Changing the factory setting of a function button If the factory settings of the FUNCTION buttons don't match your system components, you can change them. For example, if you have an MD player and a tape deck and you don't have a CD player, you can assign the CD/ SACD button to your tape deck. Note that the settings of the TUNER and FN SHIFT functions (VIDEO 1, VIDEO 2, VIDEO 3, PHONO and MD/TAPE) button cannot be changed. www..com SLEEP 1 2 Hold down the Function button whose function you want to change (for example, CD/SACD). Press the corresponding button of the component you want to assign to the Function button (for example, 4 - Tape deck). The following buttons are assigned to select the functions: To operate CD player DAT deck MD deck Press 1 2 3 4 5 6 7 8 9 0 >10 ENTER . AV ?/1 AV ?/1 SYSTEM STANDBY ?/1 ?/1 Tape deck A Function buttons Tape deck B LD player VCR (remote control mode VTR 1*) g FUNCTION VIDEO 1 VIDEO 2 VIDEO 3 VIDEO DVD/LD TV/SAT PHONO AUX MD/TAPE FN SHIFT CD/SACD MENU TUNER F 1 4 2 5 3 6 G ENTER Numeric buttons VCR (remote control mode VTR 2*) VCR (remote control mode VTR 3*) TITLE f 7 8 0 SWAP 9 RETURN >10 = SHIFT >10 - /- - ENTER D.TUNING ENTER TV DSS (Digital Satellite Receiver) DVD VCD player POSITION = 0 DISPLAY + D.SKIP/ CH/PRESET ANT TV/VTR - SUB CH + ) P IN P 9 JUMP ( WIDE DISC TV/ VIDEO P p MULTI CH/ 2 CH DIRECT SOUND FIELD 2CH/OFF A.F.D. - MODE + MUTING * Sony VCRs are operated with a VTR 1, 2 or 3 setting. These correspond to Beta, 8mm and VHS respectively. Additional Information TEST TONE MAIN MENU MENU MASTER VOL Now you can use the CD/SACD button to control the tape deck. MASTER VOL - To reset a button to its factory setting Repeat the above procedure. To reset all the function buttons to their factory setting Press ?/1, AV ?/1 and MASTER VOL - at the same time. 52 Index A Adjusting brightness of the display 21 speaker volumes 18 surround parameters 32 Automatic tuning 38 H Hookups MULTI CH IN Input 9 AC power cord 10 antennas 5 audio components 6 digital components 8 speaker system 12 video components 7 S Scanning preset stations. See Preset tuning radio stations. See Automatic tuning Selecting component 23 sound field 26 Sleep timer 42 Sound field adjustable parameters 32 customizing 32 pre-programmed 26-29 resetting 34 selecting 26 Speakers adjusting speaker volume 18 connection 12 placement 15 Supplied accessories 4 Surround sound 25-35 B Basic receiver operations 21-24 Batteries 4 www..com I, J, K Indexing. See Naming C Changing display 21 effect level 32 Checking the connections 19 Clearing receiver's memory 14 Connecting. See Hookups Customizing sound fields 34 L, M Labeling. See Naming N, O Naming preset stations 41 program sources 41 D Demonstration mode 14 Digital Cinema Sound 48 Direct tuning 38 Dolby Digital 48 Dolby Pro Logic Surround 48 Dubbing. See Recording P, Q Parameter 32, 34 Preset stations how to preset 39 how to tune 38 Preset tuning 39 T Test tone 18 Troubleshooting 44 Tuning automatically 38 directly 38 preset stations 39 E, F, G Editing. See Recording Effect level 32 R Receiving broadcasts automatically 38 directly 38 preset stations 39 Recording on an audio tape or MD 41 on a video tape 42 Additional Information U, V, W, X, Y, Z Unpacking 4 53 www..com Sony Corporation Printed in Indonesia http://www.world.sony.com/ |
Price & Availability of STR-DE575
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |